The Unofficial JGMaker (& JGAurora) Wiki

This is a sitemap over all available pages ordered by namespaces.

a5
modifications
a5-filament-sensor
Automatic Control The Cold End Fan
Babystepping
Tips to help your A5 prints stick!
Modifying A5/A3S with an Automatic Bed Levelling Probe
Levelling your bed correctly on the A5/A3S
Flashing a new bootloader on the A5/A3S
Where to buy JGAurora A5 & A3S 3D Printers
Damping the Bowden extruder for noise reduction
How-to open the main chassis
Cable Damage from Drag Chain
Restoring back to Official Factory OEM Firmware
faq-facebook
FAQ: Troubleshooting for JGAurora A5 & A3S
Fixing Faulty Temperature Readings
A5/A3S filament Sensor problem
A5 & A3S Custom Community Firmware
getting-started-test
New Owners Guide: Getting Started
Hot End Parts and Maintenance
Before you buy: General A5 & A3S Information
Insulating Heated Bed
jgcreat-install
Layer Shifting
A5 & A3S MKS-TFT28 LCD firmware
You probably plugged the LCD connector into the wrong socket! There are two of them - what a trap!
Make the A5 quieter
Mesh Bed Levelling
Using & Modifying your A5 or A3S
Installing a Raspberry Pi with OctoPi inside the JGAurora A5 chassis
PIZERO OCTOPI
open-chassis
Getting Started: Printing Settings
Programmable Power Supply Control
Reduce Power Supply Noise
Remove Fan PWM Noise
Replace the LCD Screen
Silence the Bowden extruder coupler while retracting
Silent Stepper Driver TMC2130
Silent Stepper Driver TMC2208
Spare Parts
Tuning & Upgrading the Stepper Drivers
Install TL-Smoothers to Reduce Salmon Skinning
Stepper Driver Upgrades: TMC2100, TMC2130, TMC2208
a5s
playground
wiki
z-603s
3d-printer-beginner-advice
JGAurora A3 Wiki
a3s
JGAurora A4 3D printer
JGAurora A5 & A3S
JGAurora (JGMaker) A5S & A1
JGAurora A5X
JGAurora A7
a8
a8s
a9
About the JGAurora Wiki
Before you buy
A5 / A5S - Burned Bed Connectors
Buy JGAurora 3D Printer
cant-adjust-bed-any-higher
China Only
JGAurora E7, A8, A8S, A9 3D Printer
contact-jgaurora
JGAurora / JGMaker Contact Details
contact
COUPON PROMOS!
COUPON & DEAL PROMOS!
e3
e7
essentials-test
Essential 3D Printer Tools, Accessories & Parts
Unreleased & Unannounced Models
General JGAurora Troubleshooting
Help with the Wiki
International Users
JGAurora, GPL & Open Source
JGCreat
JGMaker Magic 3D Printer
3D Printer Lubrication & Grease
Heating Problems
Problem with prints squished in the corner
Privacy Policy
How to find out what is wrong: lets show the error messages!
sandbox
Starting & Ending GCode
Welcome to the JGMaker (Previously JGAurora) Wiki
Template Sections
Thermal Runaway Protection: An introduction to the thermal safety systems in the Marlin Firmware
JGAurora Warranty Policy
JGAurora Z-602
JGAurora Z-603
JGAurora Z-603S 3D printer
JGAurora Z-605
JGAurora Z-605S

The Unofficial JGMaker (& JGAurora) Wiki

User Tools

Site Tools

Sitemap