start-and-end-gcode
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
| start-and-end-gcode [2019/11/16 12:59] – [Ending GCode] samuelpinches | start-and-end-gcode [2020/04/28 23:48] – [Starting GCode] samuelpinches | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | e4444======Starting & Ending GCode ====== | + | ======Starting & Ending GCode ====== |
| In your slicer you will have a section for GCode commands that are run at the very start and end of every print. In Cura/ | In your slicer you will have a section for GCode commands that are run at the very start and end of every print. In Cura/ | ||
| Line 17: | Line 17: | ||
| ===Default Start Script=== | ===Default Start Script=== | ||
| * G28 ; Home all axis | * G28 ; Home all axis | ||
| - | * G1 Z15.0 F6000 ; Move up 15mm at 6000mm/min (note: more than the max speed set in the printer firmware) | + | * G1 Z15.0 F1000 ; Move up 15mm at 1000mm/min |
| * G92 E0 ; Reset extruder length to zero | * G92 E0 ; Reset extruder length to zero | ||
| * G1 F200 E10 ; Extrude 10mm at 200mm/min | * G1 F200 E10 ; Extrude 10mm at 200mm/min | ||
| Line 31: | Line 31: | ||
| * G28 ; Home all axis | * G28 ; Home all axis | ||
| - | * G1 Z15.0 F6000 ; Move up 15mm at 6000mm/min (note: more than the max speed set in the printer firmware) | + | * G1 Z15.0 F1000 ; Move up 15mm at 1000mm/min |
| * G92 E0 ; Reset extruder length to zero | * G92 E0 ; Reset extruder length to zero | ||
| * G1 X0.0 Y0.0 F1000.0 ; go to edge of print area | * G1 X0.0 Y0.0 F1000.0 ; go to edge of print area | ||
| Line 69: | Line 69: | ||
| * M140 S[first_layer_bed_temperature] | * M140 S[first_layer_bed_temperature] | ||
| * M109 S[first_layer_temperature_0] | * M109 S[first_layer_temperature_0] | ||
| - | // | + | |
| - | For Cura [[https:// | + | For Cura you can add additional wait commands to the start gcode if you want, but note that the format is slightly different |
| * M190 S{print_bed_temperature} ; Set bed temp. | * M190 S{print_bed_temperature} ; Set bed temp. | ||
| * M140 S{print_bed_temperature} ; Wait for bed temp. | * M140 S{print_bed_temperature} ; Wait for bed temp. | ||
| - | * M109 S{print_temperature} ; Wait for all used extruders to reach temperature.// | + | * M109 S{print_temperature} ; Wait for all used extruders to reach temperature. |
| // Thanks to Poikilos for info on Wait for temperature.// | // Thanks to Poikilos for info on Wait for temperature.// | ||
| ---- | ---- | ||
start-and-end-gcode.txt · Last modified: 2020/12/25 02:13 by 127.0.0.1
