a5:silent-stepper-driver-tmc2208
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
a5:silent-stepper-driver-tmc2208 [2018/07/07 04:01] – Need Correction Reading. aeket | a5:silent-stepper-driver-tmc2208 [2020/12/25 02:13] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ====== Under Construction ====== | + | **<WRAP center round alert 60%> |
- | {{: | + | This guide will only work on the 1.1.9 Marlin firmware for the JG A5, which is in beta and may have extra bugs. |
+ | |||
+ | A 1.1.8 version may come out if someone else is willing to do one on the wiki however I don't use 1.1.8 | ||
+ | </ | ||
+ | ** | ||
==== Silent Stepper Driver TMC2208 | ==== Silent Stepper Driver TMC2208 | ||
- | Author: AETEK | + | {{: |
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | \\ | ||
+ | Author: AETEK \\ | ||
+ | Additional information: | ||
The changes shown here require knowledge in the field of Arduino IDE, Marlin and electrical engineering and can overwhelm normal users. Also, I would like to point out possible dangers that exist in certain interventions. All adjustments have been checked for function. | The changes shown here require knowledge in the field of Arduino IDE, Marlin and electrical engineering and can overwhelm normal users. Also, I would like to point out possible dangers that exist in certain interventions. All adjustments have been checked for function. | ||
Line 8: | Line 32: | ||
**Difficulty: | **Difficulty: | ||
- | **What is this about?** \\ | + | **The advantages of the TMC2208 or why someone would want to install these** \\ |
- | The TMC2208 is a German development. I was made in Germany, too LOL. This tutorial is about making the A5 quieter. It is not my intention to explain all possible options of the TMC2208. Like me, most users will buy these stepper drivers just for one reason: to have silence. I focus on installing and configuring these drivers.\\ | + | The TMC2208 is a German development. This tutorial is about making the A5 quieter. It is not my intention to explain all possible options of the TMC2208. Like me, most users will buy these stepper drivers just for one reason: to have silence. I focus on installing and configuring these drivers.\\ |
Why use only two TMC2208?\\ | Why use only two TMC2208?\\ | ||
The most noise comes from the Y-axis and the X-axis. Because the Z-axis rarely moves when printing you do not hear much noise. The TMC2208 can deliver less power than the standard A4988 driver. One Z-axis driver needs to power two motors at the same time. The avaliable motor current is divided between both motors. \\ | The most noise comes from the Y-axis and the X-axis. Because the Z-axis rarely moves when printing you do not hear much noise. The TMC2208 can deliver less power than the standard A4988 driver. One Z-axis driver needs to power two motors at the same time. The avaliable motor current is divided between both motors. \\ | ||
Line 25: | Line 49: | ||
**Required Electrical Parts** | **Required Electrical Parts** | ||
- | * 2 x TMC2208 Stepper Driver Modules With Heatsinks | + | * [[https:// |
* Active Cooling Fan Solution< | * Active Cooling Fan Solution< | ||
* Some cable and heat shrink | * Some cable and heat shrink | ||
Line 38: | Line 62: | ||
**Please first pull the A5 mains plug**\\ | **Please first pull the A5 mains plug**\\ | ||
- | Before you install the TMC2208 module into the MKS GEN_L motherboard you should remove the pin named " | + | Before you install the TMC2208 module into the MKS GEN_L motherboard you should remove the pin named " |
{{: | {{: | ||
- | If you Upgrade | + | If you upgrade |
When inserting the modules into the sockets, it must be noted that the mounting direction is different as with the A4988 driver (see photos). | When inserting the modules into the sockets, it must be noted that the mounting direction is different as with the A4988 driver (see photos). | ||
Line 47: | Line 71: | ||
\\ | \\ | ||
- | ==== How to set the stepper motor current? ==== | + | ==== How to set the stepper motor current ==== |
{{: | {{: | ||
Line 60: | Line 84: | ||
\\ | \\ | ||
- | Here is an online calculator | + | The voltages below are suggested |
- | https:// | + | |
- | //I have set different VREF values and measured the temperature of the X-motor:\\ | + | Axis = Vref \\ |
- | VREF 1.41V eq. 1.0A @ 55°C motor temperature. | + | X = 0.85V \\ |
- | VREF 1.13V eq. 0.8A @ 45°C motor temperature. | + | Y = 1.25V \\ |
- | // | + | Z = 0.85V \\ |
- | At VREF = 1.41V (1.0A) the motors were too hot for me.\\ | + | E = 1.00V \\ |
- | **A good initial value is VREF = 1.13V (0.8A) \\ | ||
- | I set this value the same for the X and Y axis. So far, there were no problems.**\\ | ||
\\ | \\ | ||
This concludes work on the A5 hardware for this project. In order for the drivers to work, the Marlin firmware has to be adjusted. | This concludes work on the A5 hardware for this project. In order for the drivers to work, the Marlin firmware has to be adjusted. | ||
Line 100: | Line 121: | ||
#define INVERT_X_DIR false | #define INVERT_X_DIR false | ||
#define INVERT_Y_DIR true | #define INVERT_Y_DIR true | ||
+ | </ | ||
+ | |||
+ | **Replace this original code block...** | ||
+ | < | ||
+ | #define X_DRIVER_TYPE | ||
+ | #define Y_DRIVER_TYPE | ||
+ | </ | ||
+ | |||
+ | **...with this customized code:** | ||
+ | < | ||
+ | #define X_DRIVER_TYPE | ||
+ | #define Y_DRIVER_TYPE | ||
+ | </ | ||
+ | Make sure you install the TMC2208 Arduino library or you will get compiler errors about missing files. | ||
+ | If you want to do the extruder axis as well, make sure you invert the INVERT_E_DIR true/false as well as replace the E_DRIVER_TYPE with TMC2130 so that your firmware will use this driver properly. | ||
+ | |||
+ | The following adjustments are made in the " | ||
+ | **Replace this original code block...** | ||
+ | < | ||
+ | //#define MONITOR_DRIVER_STATUS | ||
+ | </ | ||
+ | |||
+ | **...with this customized code:** | ||
+ | < | ||
+ | #define MONITOR_DRIVER_STATUS | ||
</ | </ | ||
Line 112: | Line 158: | ||
- Use the Touch Display (Move) and check that the X and Y axes are moving in the right direction. | - Use the Touch Display (Move) and check that the X and Y axes are moving in the right direction. | ||
- | If everything reacts like that, then enjoy the silence.\\ | + | Make sure your X and Y (and Z if you also have the extra driver installed and wired) are going to correct way otherwise you'll need to make sure you did all the changes to the firmware. |
- | + | ||
- | This completes | + | |
- | \\ | + | |
- | \\ | + | |
- | ---- | + | |
- | \\ | + | |
- | Status 6. July 2018: Need Correction Reading. Tomorrow... | + |
a5/silent-stepper-driver-tmc2208.1530900080.txt.gz · Last modified: 2020/12/25 02:13 (external edit)