a5:filament-sensor
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
a5:filament-sensor [2018/02/13 06:48] – [A5/A3S filament Sensor] pinchies | a5:filament-sensor [2020/12/25 02:13] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== A5/A3S filament Sensor ===== | + | ===== A5/A3S filament Sensor |
- | ===Problem:=== | + | ====TL;DR==== |
- | The filament sensor on these printers is often plugged in wrongly into the front LCD. This causes a loud continuous beeping sound when you try to print. The printer is thinking filament has run out, and is preventing printing from proceeding. | + | |
- | Even if it is plugged in correctly, the connector that JGAurora has used can short circuit | + | **[[https:// |
+ | {{youtube> | ||
+ | ==== Filament sensor pins ==== | ||
+ | The pins for the filament sensor belong to the 6-pin header pins near the centre of the lcd module. The top two pins, in the right column of pins are used. There is a problem | ||
- | ===Solution:=== | + | Note: This issue has been resolved by JGAurora in recently manufactured machines by using hot glue to both insulate the other pins, and to hold the connector in place correctly. |
- | Unplug | + | ====Problem:==== |
+ | When you try to print, | ||
- | You can access this cable from underneath the printer, through the cavity, or by opening up the main chassis. | ||
- | If you wish to use this filament run-out feature reliably, you will either need to replace | + | ==== Diagnosis: ==== |
+ | The printer is thinking that the filament | ||
- | The two wire cable is NOT polarity sensitive, as it goes to a simple mechanical switch that detects | + | However, this function can be triggered by mistake |
+ | - If the filament sensor is plugged into the wrong pins. | ||
+ | - If the connector | ||
- | The INCORRECT way the plug comes installed from the factory | + | Checking |
- | {{ : | + | |
+ | The other way this problem can be triggered, is if the connector is touching the other pins. | ||
- | ==== Filament sensor pins ==== | + | The connector that JGAurora has used are called JST-XH connectors. These connector have both pin sockets and side contacts. **If these side contacts touch the neighbouring pins, this can also trigger the problem. ** |
- | The pins for the filament | + | {{ : |
+ | |||
+ | |||
+ | ====Solution:==== | ||
+ | **Edit: DaHai has since done a very clear [[https:// | ||
+ | |||
+ | |||
+ | A simple solution is just to unplug the two wire cable sticking out of the LCD module! | ||
+ | However, if you want to use this feature, you can do this simple trick. Turning the connect 180 degrees, will make the metal side contacts face away from the other column of pins. Note that the JST connector they are using has three sockets, but only two are used. You need to make sure that the two wires are still connecting to the same two pins, but in this case we are effectively reversing the polarity. This is not a problem – the sensor | ||
+ | |||
+ | |||
+ | If you wish to use this filament run-out feature reliably, you will either need to replace | ||
+ | |||
+ | |||
+ | The way the plug comes installed from the factory is shown in the image below. It is still recommended to flip the connector 180 degrees to orient the metal contacts away from the other neighbouring | ||
+ | {{ : | ||
+ | {{ : | ||
+ | (Top Image Credit: Markus IngK - MCK, Bottom Image Credit: [[https:// |
a5/filament-sensor.txt · Last modified: 2020/12/25 02:13 by 127.0.0.1