a5:tlsmoothers

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
a5:tlsmoothers [2018/06/14 16:57]
samuelpinches
a5:tlsmoothers [2018/11/25 04:08] (current)
samuelpinches
Line 1: Line 1:
-====== Howto: Install TL-Smoothers to Reduce Salmon Skinning ======+====== Install TL-Smoothers to Reduce Salmon Skinning ======
 The stock stepper drivers on the A5 use the Allegro A4988 stepper drivers. These drivers can be susceptible to showing "salmon skinning" on curved surfaces, or zebra striping on flat surfaces, like the cabin on a 3Dbenchie boat. The stock stepper drivers on the A5 use the Allegro A4988 stepper drivers. These drivers can be susceptible to showing "salmon skinning" on curved surfaces, or zebra striping on flat surfaces, like the cabin on a 3Dbenchie boat.
  
 These artefacts can be reduced by several methods. These artefacts can be reduced by several methods.
-One option is to install [[a5:stepper-drivers|TMC2100 stepper drivers]] to replace the A4988 stepper drivers. This has both advantages and disadvantages.+One option is to install [[a5:upgrade-stepper-drivers-tmc|TMC stepper drivers]]. This works well, but is a bit more complex to do.
  
-Another option is to install smoothing diodes - which are very easy to install. These are simple devices that are plugged in between the stepper driver board, and the stepper motor. The reason that this works is not definitively known, but the result has been conclusively proven to reduce or eliminate salmon skinning effects. These are available in both 4 diode, and 8 diode version. The best results are obtained with the 8 diode versions.+Another option is to install smoothing diodes - and these are very easy to install. These are simple devices that are plugged in between the stepper driver board, and the stepper motor. The reason that this works is not definitively known, but the result has been conclusively proven to reduce or eliminate salmon skinning effects. These are available in both 4 diode, and 8 diode version. The best results are obtained with the 8 diode versions.  
 + 
 +<WRAP center round alert 80%> 
 +**DO NOT USE TL-SMOOTHERS WITH TMC STEPPER DRIVERS — YOU WILL GET WORSE RESULTS!** 
 +</WRAP>
  
 These products are often branded "TL-smoothers", as the company who developed them is called Triangle Labs (TL). These products are often branded "TL-smoothers", as the company who developed them is called Triangle Labs (TL).
Line 19: Line 23:
   - Cover TL-smoother with insulation sleeve (usually included) to prevent touching metal frame   - Cover TL-smoother with insulation sleeve (usually included) to prevent touching metal frame
   - Unplug the printer   - Unplug the printer
-  - Open the main chassis+  - Open the main chassis  
 +  - A video guide by DaHai of opening the main A5 case/chassis can be viewed [[https://www.youtube.com/watch?v=d6lRvYPSY7A|here]].
   - Unplug the x and y axis stepper cables   - Unplug the x and y axis stepper cables
-  - plug in the short supplied cable into the motherboard, and then into one side of the TL-smoother. Then plug the cable that goes to the motor into the other side of the TL-smoother.+  - Plug in the short supplied cable into the motherboard, and then into one side of the TL-smoother. Then plug the cable that goes to the motor into the other side of the TL-smoother
 +  - You can use a heat gun to shrink the insulation tubing after installation.
   - Should look like this after installation:   - Should look like this after installation:
 {{:a5:tlsmoother-jgauroraa5.jpg?direct&500|}} {{:a5:tlsmoother-jgauroraa5.jpg?direct&500|}}
Line 34: Line 40:
  
 {{:a5:salmon-3d-benchie.jpg?direct&400|}} {{:a5:salmon-3d-benchie.jpg?direct&400|}}
 +
 +
 +====Example Video====
 +{{youtube>KMoVxF0Yd2M?medium}}
a5/tlsmoothers.1528959454.txt.gz · Last modified: 2018/06/14 16:57 by samuelpinches