a5:faq
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| a5:faq [2018/06/26 11:36] – samuelpinches | a5:faq [2020/12/25 02:13] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 33: | Line 33: | ||
| * You must " | * You must " | ||
| * You may also want to check you have [[stepper-drivers|tuned your stepper drivers]]. | * You may also want to check you have [[stepper-drivers|tuned your stepper drivers]]. | ||
| + | * Check for errors in [[/ | ||
| ---- | ---- | ||
| Line 60: | Line 61: | ||
| * Still not working? [[: | * Still not working? [[: | ||
| * Faulty temperature readings? Check [[a5: | * Faulty temperature readings? Check [[a5: | ||
| + | * Bed not heating? [[a5: | ||
| + | * Bed still not heating? [[: | ||
| ---- | ---- | ||
| Line 73: | Line 76: | ||
| * [[a5: | * [[a5: | ||
| * Check the [[https:// | * Check the [[https:// | ||
| + | |||
| + | ------------ | ||
| + | ====Problem: | ||
| + | |||
| + | * You may notice the printer restarts when starting a print, or perhaps when you preheat the bed | ||
| + | |||
| + | **Solutions: | ||
| + | |||
| + | This problem can be caused by TWO different causes: | ||
| + | |||
| + | * If your printer has a drag chain, please see [[A5: | ||
| + | * If your printer has clips on the bed, these clips may be scratching the bed heating element (underside of the bed) and causing a short circuit. Remove the clips, and place two layers of electrical tape on the underside of the bed. Then place the clips back on. | ||
| + | |||
| ------------ | ------------ | ||
| ====Problem: | ====Problem: | ||
| + | | ||
| + | {{ : | ||
| + | |||
| * When you try to home the z axis, the nozzle is still too far away from the bed. | * When you try to home the z axis, the nozzle is still too far away from the bed. | ||
| * You may find that you cannot loosen the bed screws far enough | * You may find that you cannot loosen the bed screws far enough | ||
| Line 84: | Line 103: | ||
| * By undoing the two larger screws, you should be able to adjust the vertical home position of the nozzle, to allow you to be able to properly calibrate your bed. | * By undoing the two larger screws, you should be able to adjust the vertical home position of the nozzle, to allow you to be able to properly calibrate your bed. | ||
| * There are two small holes in the black metal frame opposite those two screws. These holes will give you easier access | * There are two small holes in the black metal frame opposite those two screws. These holes will give you easier access | ||
| + | * Click on the photo to enlarge. | ||
| -------- | -------- | ||
| Line 130: | Line 150: | ||
| ====Problem: | ====Problem: | ||
| - | **Solution: | + | **Solution: |
| ----- | ----- | ||
| Line 150: | Line 170: | ||
| * Check you have plugged in the internal USB cable! | * Check you have plugged in the internal USB cable! | ||
| * Check the USB stick is formatted correctly (FAT32). | * Check the USB stick is formatted correctly (FAT32). | ||
| - | |||
a5/faq.1529976961.txt.gz · Last modified: 2020/12/25 02:13 (external edit)
